View AT043TN24V7_6949764.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

the copyright belongs to innolux. any unauthorized use is prohibited. chimei inno l u x display corporation lcd module s p e c i f i c at i o n customer: model name: at043tn24 v.7 spec no.: a043-24-tt-71 date: 2010/04/19 version: 01 preliminary specification final specification remark touch screen panel (3-in-1fpc) low power consumption for customer s acceptance approved by comment approved by review ed by prepared by joe lin 2010/04/24 jack huang james yu charlie chou 2010/04/23 charlie chou 2010/04/23 www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x the copyright belongs to innolux. any unauthorized u se is prohibited. innolux copyright 2004 all rights reserved, copying forbidden. record of revision version revise date page content pre-spec .01 2010/04/19 initial release. www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x the copyright belongs to innolux. any unauthorized use is prohibited. contents 1. general specifications 1 2. pin assignment ...2 2.1. tft lcd panel driving section.................. ................................................... ................. 2 2.2. touch screen panel section....................... ................................................... .................. 4 3. operation specifications 5 3.1. absolute maximum ratings ....................... ................................................... .................. 5 3.2. typical operation conditions ................... ................................................... ..................... 6 3.3 backlight driving conditions ...................... ................................................... ................. 6 3.4. power sequence ................................. ................................................... ........................ 7 3.5. timing characteristics .......................... ................................................... ....................... 8 3.5.1. timing conditions ........................... ................................................... ..................... 8 3.5.2. timing diagram .............................. ................................................... ..................... 9 4. touch screen panel specifications ..10 4.1. electrical characteristics ......................... ................................................... .................. 10 4.2. mechanical & reliability characteristics .......... ................................................... ........... 11 4.3. linearity definition .......................... ................................................... ............................ 12 4.4. housing design guide ..13 5. optical specifications .....14 6. reliability test items .18 7. general precautions .19 7.1. safety ........................................ ................................................... ................................. 19 7.2. handling ...................................... ................................................... ............................... 19 7.3. static electricity................................ ................................................... ........................... 19 7.4. storage ....................................... ................................................... ................................ 19 7.5. cleaning ...................................... ................................................... ............................... 19 8. mechanical drawing .20 9. package drawing .21 9.1. packaging material table........................ ................................................... .................... 21 9.2. packaging quantity.............................. ................................................... ....................... 21 9.3. packaging drawing............................... ................................................... ...................... 22 www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 1/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 1. general specifications no. item specification remark 1 lcd size 4.3 inch(diagonal) 2 driver element a-si tft active matrix 3 resolution 480 3 (rgb) 272 4 display mode normally white, transmissive 5 dot pitch 0.066(w) 0.198(h) mm 6 active area 95.04(w) 53.856(h) mm 7 module size 105.5(w) 67.2(h) 4.05(d) mm note 1 8 surface treatment anti-glare 9 color arrangement rgb-stripe 10 interface digital 11 backlight power consumption 0.558 w(typ.) 12 panel power consumption 0.056 w (typ.) 13 weight tbd (typ.) note 1: refer to mechanical drawing. www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 2/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 2. pin assignment 2.1. tft lcd panel driving section fpc connector is used for the module electronics interfac e. the recommended model is fh19sc-40s-0.5sh manufactured by hirose. pin no. symbol i/o function remark 1 v led- p power for led backlight cathode 2 v led+ p power for led backlight anode 3 gnd p power ground 4 v dd p power voltage 5 r0 i red data (lsb) 6 r1 i red data 7 r2 i red data 8 r3 i red data 9 r4 i red data 10 r5 i red data 11 r6 i red data 12 r7 i red data (msb) 13 g0 i green data (lsb) 14 g1 i green data 15 g2 i green data 16 g3 i green data 17 g4 i green data 18 g5 i green data 19 g6 i green data 20 g7 i green data (msb) www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 3/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 21 b0 i blue data (lsb) 22 b1 i blue data 23 b2 i blue data 24 b3 i blue data 25 b4 i blue data 26 b5 i blue data 27 b6 i blue data 28 b7 i blue data (msb) 29 gnd p power ground 30 clk i pixel clock 31 disp i display on/off 32 nc - no connection 33 nc - no connection 34 de i data enable 35 nc - no connection 36 gnd p power ground 37 x1 i/o right electrode C differential analog 38 y1 i/o bottom electrode C differential analog 39 x2 i/o left electrode C differential analog 40 y2 i/o top electrode C differential analog i: input, o: output, p: power www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 4/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 2.2. touch screen panel section pin no. symbol i/o function remark 1 x1 right right electrode C differential analog 2 y1 bottom bottom electrode C differential analog 3 x2 left left electrode C differential analog 4 y2 top top electrode C differential analog note: touch screen panel block top view www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 5/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 3. operation specifications 3.1. absolute maximum ratings (note 1) values item symbol min. max. unit remark power voltage v dd -0.5 5.0 v input signal voltage logic input -0.5 5.0 v operation temperature t op -20 70 note 3, 4 storage temperature t st -30 80 note 3, 4 led reverse voltage v r - 1.2 v each led note 2 led forward current i f - 25 ma each led note 1: the absolute maximum rating values of this pr oduct are not allowed to be exceeded at any times. a module should be used with a ny of the absolute maximum ratings exceeded, the characteristics of the modu le may not be recovered, or in an extreme condition, the module ma y be permanently destroyed. note 2: v r conditions: zener diode 20ma note 3: 90% rh max. (max wet temp. is 60 ) maximum wet-bulb temperature is at 60 or less. and no condensation (no drops of dew) ( ) note 4: in case of temperature below 0 ,the response time of liquid crystal (lc) becomes slower and the color of panel darker than normal one. +60 , 90%rh www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 6/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 3.2. typical operation conditions values item symbol min. typ. max. unit remark power voltage v dd 3.1 3.3 3.5 v current for driver iv dd - 17 25 ma v dd = 3.3v input logic high voltage v ih 0.8v dd - v dd v input logic low voltage v il gnd - 0.2v dd v note 1 note1: clk, de, r0~ r7, g0~ g7, b0~ b7. 3.3 backlight driving conditions values item symbol min. typ. max. unit remark voltage for led backlight v l 25.2 27.9 31.5 v note 2 current for led backlight i l 18 20 22 ma led life time - 20,000 - - hr note 1 note 1: the led life time is defined as the module brightness decrease to 50% original brightness that the ambient temperature is 25 and i l =20ma. the led lifetime could be decreased if operating i l is lager than 20 ma. note 2: the led supply voltage is defined by the num ber of led at ta=25 and i l =20ma. www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 7/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 3.4. power sequence to prevent a latch-up or dc operation of the lcd mo dule, the power on/off sequence should be as the diagram below. symbol specification symbol specification t1 0 Q t1 Q 10 msec t4 160 msec Q t4 t2 0 Q t2 Q 100 msec t5 160 msec Q t5 t3 0 Q t3 Q 200 msec t6 1 msec Q t6 www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 8/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 3.5. timing characteristics 3.5.1. timing conditions parallel de mode rgb input timing table value parameter symbol min. typ. max. unit clk frequency fclk 7 9 12 mhz dev period time tv 277 288 400 h dev display area tvd 272 h dev blanking tvb 5 16 128 h deh period time th 520 525 800 clk deh display area thd 480 clk deh blanking thb 40 45 320 clk clk cycle time tclk 83 110 143 ns clock width of high level tcwh 40 50 60 % clock width of low level tcwl 40 50 60 % clock rising time t rck - 9 ns clock falling time t fck - 9 ns data setup time t desu 10 - - ns data hold time t dahd 10 - - ns de setup time t desu 10 - - ns de hold time t dehd 10 - - ns www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 9/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 3.5.2. timing diagram www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 10/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 4. touch screen panel specifications 4.1. electrical characteristics value item min. typ. max. unit remark linearity -1.5 - 1.5 % analog x and y directions 300 - 1500 ? x terminal resistance 100 - 900 ? y insulation resistance 25 - - m? dc 25v voltage - 5 7 v dc chattering - - 10 ms 100k? pull-up transparency 80 - - % jis k7105 note: avoid operating with hard or sharp material su ch as a ball point pen or a mechanical pencil except a polyacetal pen (tip r0.8mm or less) or a finger. www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 11/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 4 .2. mechanical & reliability characteristics value item min. typ. max. unit remark activation force 80 - - gf note 1 durability-surface scratching write 100,000 - - characters note 2 durability-surface pitting 1,000,000 - - touches note 3 surface hardness 3 - - h jis k5400 note 1: activation force test condition (1) input dc 5v on x direction, drop off polyacetal s tylus (r0.8), until output voltage stabilize ,then get the activation fo rce (2) r8.0mm silicon rubber for finger activation force test (3) test point: 9 points note 2: measurement for surface area. -scratch 100,000 times straight line on the f ilm with a stylus change every 20,000 times. -force: 250gf. -speed: 60mm/sec. -stylus: r0.8 polyacetal tip. note 3: pit 1,000,000 times on the film with a r0 .8 silicon rubber. -force: 250gf. -speed: 2times/sec. www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 12/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 4.3. linearity definition va: maximum voltage in the active area of touch panel vb: minimum voltage in the active area of touch panel x: random measuring point vxm: actual voltage of lx point vxi: theoretical voltage of lx point linearity = [|vxi-vxm |/(va-vb)]*100% note: test area is as follows and operation force is 150 gf. 2.0mm test area active area 2.0mm 2.0mm 2.0mm www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 13/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 4.4. housing design guide housing design follow as below 1) avoid the design that housing overlap and press on the active area of the lcm 2) give enough gap(over 0.5mm at compressed) between the housing and tsp to protect wrong operating. 3) use a buffer material(gasket) between the tsp and housing to protect damage and wrong operating 4) avoid the design that buffer material overlap and press on the inside of tsp view area. www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 14/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 5. optical specifications values item symbol condition min. typ. max. unit remark l =180(9 oclock) 60 70 - r =0(3 oclock) 60 70 - t =90(12 oclock) 40 50 - viewing angle (cr 10) b =270(6 oclock) 60 70 - degree note 1 note 7 t on - 10 20 msec note 3 response time t off - 15 30 msec note 3 contrast ratio cr 400 500 - - note 4 w x 0.26 0.31 0.36 - color chromaticity w y 0.28 0.33 0.38 - note 2 note 5 note 6 note 7 luminance l 350 400 - cd/m2 note 6 luminance uniformity y u normal ==0 70 75 - % note 8 test conditions: 1. v dd =3.3v, i l =20ma (backlight current), the ambient temperature is 2 5 . 2. the test systems refer to note 2. www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 15/22 the copyright belongs to innolux. any unauthorized u se is prohibited. note 1: definition of viewing angle range fig. 4-1 definition of viewing angle note 2: definition of optical measurement system . the optical characteristics should be measure d in dark room. after 30 minutes operation, the optical properties are measured at the center point of the lcd screen. (response time is measured by photo detector topc on bm-7, other items are measured by bm-5a/field of view: 1 /heigh t: 500mm.) fig. 4-2 optical measurement system setup normal line ==0 normal line ==0 photo detector =90 12 oclock direction =270 6 oclock direction =0 =180 active area 500mm =90 12 oclock direction =270 6 oclock direction =0 =180 active area l t b r www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 16/22 the copyright belongs to innolux. any unauthorized u se is prohibited. note 3: definition of response time the response time is defined as the lcd optical switching time interval between white state and black state. rise time (t on ) is the time between photo detector output intensity changed from 90% to 1 0%. and fall time (t off ) is the time between photo detector output intensity chang ed from 10% to 90%. fig. 4-3 definition of response time note 4: definition of contrast ratio state black" " the on lcd when measured luminance state white" " the on lcd when measured luminance (cr) ratio contrast = note 5: definition of color chromaticity (cie1931 ) color coordinates measured at center point of lcd. note 6: all input terminals lcd panel must be ground while measuring the center area of the panel. the led driving condition is i l =20ma. note 7: the values shall be measured without touch scr een panel. 100% 90% 10% 0% photo detector output (relative value) t on t off white (tft off) black (tft on) white (tft off) www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 17/22 the copyright belongs to innolux. any unauthorized u se is prohibited. note 8: definition of luminance uniformity active area is divided into 9 measuring areas (refer t o fig. 4-4 ).every measuring point is placed at the center of each measur ing area. max min b b (yu) uniformity luminance = l-------active area length w----- active area widt h w w/3 w/3 w/6 l/3 l/3 l/6 l fig. 4-4 definition of measuring points b max : the measured maximum luminance of all measurement po sition. b min : the measured minimum luminance of all measurement po sition. www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 18/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 6. reliability test items (note3) item test conditions remark high temperature storage ta = 80 240 hrs note 1,note 4 low temperature storage ta = -30 240hrs note 1,note 4 high temperature operation ts = 70 240hrs note 2,note 4 low temperature operation ta = -20 240hrs note 1,note 4 operate at high temperature and humidity +60 , 90%rh 240 hrs note 5 thermal shock -30 /30 min ~ +80 /30 min for a total 100 cycles, start with cold temperature and end with high temperature note 4 vibration test frequency range:10~55hz stroke:1.5mm sweep:10hz~55hz~10hz 2 hours for each direction of x. y. z. (6 hours for total) mechanical shock 100g 6ms,x, y, z 3 times for each direction package vibration test random vibration : 0.015g*g/hz from 5-200hz, -6db/octave from 200-500hz 2 hours for each direction of x. y. z. (6 hours for total) package drop test height:60 cm 1 corner, 3 edges, 6 surfaces electro static discharge 2kv, human body mode, 100pf/1500? note 1: ta is the ambient temperature of samples. note 2: ts is the temperature of panels surface. note 3: in the standard condition, there shall be no practical problem that may affect the display function. after the reliability test, the prod uct only guarantees operation, but doesnt guarantee all the cosmetic specification. note 4: before cosmetic and function tests, the product must have enough recovery time, at least 2 hours at room temperature. note 5: before cosmetic and function tests, the product must have enough recovery time, at least 24 hours at room temperature. www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 19/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 7. general precautions 7.1. safety liquid crystal is poisonous. do not put it in your mouth . if liquid crystal touches your skin or clothes, wash it off immediately by using so ap and water. 7.2. handling 1. the lcd panel is plate glass. do not subject the pane l to mechanical shock or to excessive force on its surface. 2. the polarizer attached to the display is easily da maged. please handle it carefully to avoid scratch or other damages. 3. to avoid contamination on the display surface, do no t touch the module surface with bare hands. 4. keep a space so that the lcd panels do not touch o ther components. 5. put cover board such as acrylic board on the surface of lcd panel to protect panel from damages. 6. transparent electrodes may be disconnected if you use the lcd panel under environmental conditions where the condensation of de w occurs. 7. do not leave module in direct sunlight to avoid malfunction o f the ics. 7.3. static electricity 1. be sure to ground module before turning on power or operating module. 2. do not apply voltage which exceeds the absolute maxi mum rating value. 7.4. storage 1. store the module in a dark room where must keep at 2510 and 65%rh or less. 2. do not store the module in surroundings containing organic solvent or corrosive gas. 3. store the module in an anti-electrostatic container or bag. 7.5. cleaning 1. do not wipe the polarizer with dry cloth. it migh t cause scratch. 2. only use a soft sloth with ipa to wipe the polarize r, other chemicals might permanent damage to the polarizer. www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 20/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 8. mechanical drawing www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 21/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 9. package drawing 9.1. packaging material table no. item model (material) dimensions (mm) unit weight (kg) quantity (pcs) remark 1 lcm module at043tn24 v.7 105.5 67.2 4.05 tbd 160 2 partition bc corrugated paper 512 349 106 1.102 2 3 corrugated bar bc corrugated paper 349 173 0.030 8 4 dust-proof bag pe 700 530 0.060 1 5 corrugated board-1 b c corrugated paper 510 343 0.130 2 6 corrugated board-2 b c corrugated paper 1152 512 0.260 1 7 a/s bag pe 132 117 0.002 160 8 carton co rru ga t e d pap e r 530 355 255 1.100 1 9 total weight t b d 9.2. packaging quantity (1) lcm quantity per partition: 2rows x 40quantity per row = 80 pcs (2) total lcm quantity in carton: 2 layer x 80 pcs pe r partition = 160 pcs www.datasheet.co.kr datasheet pdf - http://www..net/
chimei inno l u x spec no.: a043-24-tt-71 date : 2010/04/19 page : 22/22 the copyright belongs to innolux. any unauthorized u se is prohibited. 9.3. packaging drawing www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of AT043TN24V7

	To Download AT043TN24V7 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .